凈化風管的質量直接關系到體系是否到達規劃參數和正常運用要求，其制造一般選用工廠集中制造和現場制造兩種方法。無論選用哪種制造方法，都要確保制造場地的潔凈和關閉，好選用水泥地上或地上鋪設金屬鋼板，其面積不得小于100m?，且滿足采光和照明條件，制造完結的凈化風管要進行堆積，并進行看守;如果選用現場預制時，要確保預制完結后的風管能夠及時運施工現場，盡量削減風管搬運的間隔，這樣能夠避免運輸過程中對風管的污染。

The quality of the purification air duct is directly related to whether the system meets the planning parameters and normal operation requirements. Its manufacturing generally adopts two methods: centralized factory manufacturing and on-site manufacturing. Regardless of the manufacturing method used, it is necessary to ensure the cleanliness and closure of the manufacturing site. It is recommended to use cement or metal steel plates laid on the ground, with an area not less than 100m?, And meet the lighting and lighting conditions, the completed purified air ducts must be stacked and guarded; If on-site prefabrication is used, it is necessary to ensure that the completed air duct can be transported to the construction site in a timely manner, and to minimize the interval between air duct handling, so as to avoid pollution to the air duct during transportation.

2.風管的規劃裝置

2. Planning device for air ducts

風管板厚的挑選

Selection of duct plate thickness

板厚對風管的質量影響較大，為了確保風管的重量，要選用小板厚的風管，可是選用的過程還是和風管的尺度和壓力等級有關。在我國，大部分的金屬風管選用的是熱鍍鋅鋼板和鋼帶，他的基體是冷軋低碳結構鋼板，其抗拉強度>270 ，延伸率>24%，厚度允許差值為d=0.6-1.2mm規模內(±0.07-0.13mm)，由于我國的工業技術和檢測技術與國外具有必定差距，國內選用的風管板厚要比國外標準大20%，但跟著我國經濟技術的不斷開展，許多國內廠商已經有才能出產厚度均勻的板材，因而在風管挑選小板厚時，要挑選差錯規模小的鋼板，避免造成鋼材的糟蹋。

The thickness of the plate has a significant impact on the quality of the air duct. In order to ensure the weight of the air duct, smaller plate thickness air ducts should be selected. However, the selection process is still related to the scale and pressure level of the air duct. In China, the majority of metal air ducts are made of hot-dip galvanized steel plates and steel strips. The base material is cold-rolled low-carbon structural steel plates, with tensile strength>270, elongation>24%, and allowable thickness difference within the range of d=0.6-1.2mm (± 0.07-0.13mm). Due to the certain gap between China's industrial technology and testing technology and foreign countries, the thickness of air duct plates used domestically is 20% larger than foreign standards. However, with the continuous development of China's economy and technology, many domestic manufacturers have been able to produce uniformly thick plates. Therefore, when selecting small plate thicknesses for air ducts, it is necessary to select steel plates with small error sizes to avoid wasting the steel.

此外，從規劃角度來看，值得注意的是一個體系能夠一起存在幾種對應于不同靜壓等級的風管板厚。在正壓風管體系的末端或負壓風管的前端，往往能夠選用低壓風管，而挨近風機的部位能夠選用中壓或高壓風管。

Furthermore, from a planning perspective, it is worth noting that a system can have several duct plate thicknesses corresponding to different static pressure levels together. At the end of a positive pressure air duct system or the front end of a negative pressure air duct, low pressure air ducts can often be used, while medium pressure or high pressure air ducts can be used near the fan.

風管的橫向銜接

Horizontal connection of air ducts

橫向銜接不僅是連續風管長度的一種手法，也能夠起著增強剛度及保持風管地橫向尺度的效果。通常橫向銜接的方法是角鋼法蘭銜接，這種銜接方法取決于壁厚，更取決于銜接種類及板壁加固方法。橫向銜接中的無法蘭銜接在低、中壓中等尺度(矩形長邊小于1.6m)的風管中的廣泛的運用。

Horizontal connection is not only a technique for continuous duct length, but also plays a role in enhancing stiffness and maintaining the horizontal scale of the duct. The usual method of horizontal connection is angle steel flange connection, which depends on the wall thickness, as well as the type of connection and the reinforcement method of the plate wall. The flange free connection in horizontal connection is widely used in low and medium scale (rectangular long side less than 1.6m) air ducts.

更多的關于山東通風管道加工的問題或者詳細的內容，請進入我們公司的網站： http://m.shanghaizhuangxiu8.com網站中會有很多的內容僅供參考

For more questions or detailed information about the processing of ventilation ducts in Shandong, please visit our company's website: http://m.shanghaizhuangxiu8.com There will be a lot of content on the website for reference only

上一篇：通風管道保障通風效果和性的加工要點
下一篇：酒店餐廳廚房排煙罩怎么確保空氣的質量？